Slickenside
A slickenside is a smoothly polished, striated fault-plane surface produced by frictional abrasion and mineral fiber growth during rock-on-rock shear slip.
A slickenside is a smoothly polished, often glossy fault surface adorned with parallel linear grooves, ridges, or mineral-fiber growths—called slickenlines—formed by frictional sliding between opposing rock walls during tectonic faulting, bedding-plane slip, or landslide shear. Because slickenlines align directly parallel to the slip vector between the hanging wall and footwall, slickensides serve as primary field kinematic indicators in structural geology for reconstructing ancient paleostress orientations and fault displacement directions.
While early usage sometimes treated slickenside and slickenline interchangeably, modern structural terminology reserves slickenside for the polished planar surface itself and slickenlines (or striations) for the linear features inscribed upon it.
Formation Mechanisms: Abrasion vs. Syn-Kinematic Mineral Fibers
Field and microstructural studies show that slickensides form through two contrasting mechanical and chemical regimes depending on depth, fluid pressure, and slip rate:
- Abrasive (Wear-Groove) Slickenlines: Under brittle upper-crustal dry or rapid slip, hard asperities (such as quartz grains or pyrite cubes) on one fault wall plow parallel micro-grooves and comminute fine fault gouge along the opposing wall, creating mirror-like polished surfaces (fault mirrors) in carbonates, quartzites, and ultramafic serpentinites.
- Mineral-Fiber (Accretionary) Slickenfibers: During slow, fluid-assisted pressure-solution creep in limestone, shale, or low-grade metamorphic rocks, mineral-rich pore fluids precipitate elongated fibrous crystals—typically calcite, quartz, gypsum, or chlorite—inside tiny dilational jogs behind asperity steps on the fault plane. As slip proceeds incrementally, fibers grow parallel to the instantaneous motion vector, preserving curved trajectories if stress rotated over time.
Determining Sense of Shear from Fault Steps
Although slickenlines reveal the line of motion (axis of slip), determining which direction the missing block moved (normal, reverse, or strike-slip sense) requires inspecting asymmetric stepped microstructures:
- Accretionary Steps: Mineral-fiber slickenfibers grow on the lee (down-step) side of asperities; running a fingertip along the surface feels smooth in the direction the missing opposite block moved and rough against it.
- Riedel (R) Fracture Steps: Brittle secondary shear fractures dipping gently into the fault wall create steps facing away from the missing block's motion—the opposite roughness asymmetry of mineral-fiber steps—making microscopic inspection essential before assigning fault-slip polarity!
Paleostress Inversion and Earthquake Physics
By measuring fault-plane strike/dip and slickenline rake (pitch) across dozens of mesoscale faults in an outcrop, geologists apply Wallace–Bott paleostress inversion to compute the principal stress axes (sigma1, sigma2, sigma3) that drove mountain building or continental rifting. Meanwhile, nano-polished hematite and carbonate fault mirrors are studied experimentally as signatures of flash heating and dynamic fault weakening during seismic rupture.
Nano-Scale Tribology and Field Preservation Bias
Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) of glossy carbonate and silicate fault mirrors reveal ultra-smooth surfaces composed of sintered nanoparticles (10 to 100 nanometers across) formed by mechanical grain comminution and frictional flash heating during seismic slip rates (~0.1 to 1 meter per second). In the field, slickensides are most prominently preserved on cohesive, fine-grained rocks (limestones, cherts, quartzites, shales, and serpentinites) along minor fault splays rather than in wide, unconsolidated fault-breccia zones, so structural geologists check whether measured mesoscale slickenlines reflect the regional master fault kinematics or local block-rotation accommodation.
Mineralogy of Slickenfibers and Geothermal Alteration
The mineral composition of accretionary slickenfibers provides a direct thermometer for the depth and temperature of fault slip. Near-surface faults in limestones precipitate fibrous calcite or gypsum, greenschist-facies crustal faults grow quartz, epidote, and chlorite fibers, and serpentinized oceanic fault zones develop fibrous chrysotile and talc slickensides whose low frictional strength promotes aseismic creep rather than locked megathrust earthquakes.
Frequently Asked Questions
What is the difference between a slickenside and a slickenline?
In modern structural geology nomenclature, a slickenside is the smoothed, polished planar fault surface as a whole, whereas slickenlines (or striae) are the parallel mechanical scratches, wear grooves, or fibrous mineral growths inscribed upon that surface marking the instantaneous or finite slip axis.
Can you determine fault motion direction just by feeling a slickenside with your hand?
Relying solely on fingertip touch ("smooth versus rough") frequently misleads because brittle Riedel (R) fracture steps feel smooth in the opposite direction of accretionary calcite- or quartz-fiber steps; structural geologists inspect micro-steps with a hand lens or petrographic thin section to verify whether stepped faces preserve mineral fibers or tensile fracture edges.
Do slickensides only form on large tectonic faults?
No. Slickensides also develop on small flexural-slip bedding planes inside buckle-folded sedimentary strata, in clay-rich vertisol soils undergoing seasonal shrink–swell shear, along the basal detachment surfaces of landslides, and along subglacial till interfaces.
Can a single slickenside surface record multiple tectonic events?
Yes. Cross-cutting sets of slickenlines with different rake angles—or superposed, shingled calcite-fiber sheets oriented in contrasting azimuths—preserve a relative chronological record of rotating paleostress fields and reactivated fault-slip vectors across successive tectonic phases.
Why are talc and serpentine slickensides associated with creeping faults?
Sheet-silicate phyllosilicates such as talc, chrysotile, lizardite, and smectite clay possess weak interlayer van der Waals bonds; when smeared along slickenside planes, they reduce the steady-state friction coefficient μ below 0.2, promoting stable aseismic fault creep rather than stick–slip earthquakes.
References
- Means, W. (1987). A newly recognized type of slickenside striation. Journal of Structural Geology. https://doi.org/10.1016/0191-8141(87)90143-x90143-x)
- Petit, J. (1987). Criteria for the sense of movement on fault surfaces in brittle rocks. Journal of Structural Geology. https://doi.org/10.1016/0191-8141(87)90145-390145-3)
- Power, W. L., & Tullis, T. E. (1992). The contact between opposing fault surfaces at Dixie Valley, Nevada, and implications for fault mechanics. Journal of Geophysical Research: Solid Earth. https://doi.org/10.1029/92jb01059